Thinkcar Thinkscan Max Auto OBD2 Diagnostic Tools Full System ECU Coding Bidirectional Control 28 Reset Launch CRP909X MK808

Thinkscan Max as the 2021 Highest-level FULL OBD II Diagnostic Device For DIY users supported include Code Reading/Clearing data stream,Actuation Test ,Special Functions etc
1.Free system-wide code reading, code clearing, data streaming and upgrades for all models.
2.The full reset function is free to use (currently 16 and will be increased to 26-28 later).
3.After subscribing to the software, the whole system can be diagnosed with full functions (action test, special function, cding can be carried out).
4.Android system can be upgraded online.
5.The whole system diagnoses more than 93 automobile brands.
6.Diagnosis covers all models that support OBD protocol after 1996.
7.Equipped with VIN code intelligent identification models.
8.THINKCAR series design, dustproof, shockproof, easy to store
9.5.99-inch display is convenient for you to diagnose the car in real time
10.2G RAM/ 16G ROM,Support Bluetooth and WiFi connection
11.Pay for one Car model software can enjoy Free Upgrade 1 year the full system ,Such as :ECU Coding/ Action Test and other Special Function
Cost: $49.95/year (you can buy from ThinkCar Store directly)

Product Homepage Function

1. Intelligent diagnosis, automatic identification of vin, enter the diagnosis system
2. Maintenance service, maintenance service download, enter the system
3. THINKCAR mall, subscription software, software upgrade, realize full-function diagnosis
4. Online upgrade , The software version can be updated
5. Vehicle files, save the data records of the detected vehicles, such as: report 6. Settings

Intelligent diagnosis

"Insert the connector into the vehicle OBD interface, and the host can be connected to the connector. In the intelligent diagnosis mode, it can automatically read the vin identification vehicle information. If the special vehicle cannot be identified, the vehicle can also be manually selected for detection. After entering the system, the basic functions of the whole system of the vehicle can be tested (not including: action test, special function, cding), code reading, code clearing, real-time data flow chart display, combined display can be performed. Support obd full-function intelligent diagnosis. Purchase a model software separately, which can be upgraded to full-system full-function.
Cost: 49.95 USD Valid for 1 year, free upgrade during the valid period"

Support to ECU Coding

The Coding function is used to re-flash the vehicle control modules.It is used to reprogram adaptive data for vehicle control modules after repairs or replacements of vehicle parts;Provide solutions for the issues of Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts etc.;Brake the limitations and restrictions; make full use of the car hidden features, like change the chimes on car, set how many times the one-touch signal flickers for one touch, remember settings for Start/Stop systems, and more.

Support Active Test (Actuation Test)

"Uses the ThinkDiag App to test if the actuator is normal, without using the vehicle’s controls, to get a significant boost in effectiveness:
[ Turn on the radiator fan | Modulate the throttle | Open/close windows | Operate mirrors | Turn on/off the lights | Turn on/off the sound horn | Test door lock … ]"

Support All System Diagnostic:

"With superior all systems diagnoses, this multipurpose obd2 scanner can be used to read all available systems’ECU information to facilitate the vehicle diagnosis.The complete systems vary from different cars and they usually include engine, transmission, ABS, SRS, SAS, TPMS, EPB and chassis / body / electrical equipment system etc.
* Examinate your car like a professional mechanical technician
*Read DTCs from the vehicle’s all electronic control systems to locate problem areas, and offer solutions;
*Erase the codes easily after DTCs retrieving and certain repairs have been carried out and turn off fault Indicator lamp;
*Live data shows each sendor parameter item displayed in analog, text, waveform graph modes etc.;
*The active test used to access vehicle-specific subsystem and component tests."

Support 28 Reset Services

"THINKSCAN max currently supports 16 maintenance software, which will be increased to 26-28 in the future. The maintenance software is completely free to use and free to upgrade.
1.Oil Reset ：allows you to perform reset for a new calculation of Engine Oil Life system once changed the oil.
2.EPB Reset ：is important in the maintenance of electronic braking system's safety and efficiency.
3.BMS Reset:allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle.
4.DPF Reset:specially works for Diesel Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.
5.SAS Reset:helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.
6.TPMS Reset :makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors.
7.IMMO reset:it is mainly used to disable the lost vehicle keys and program a new replacement key fob.
8.ABS Bleeding:ABS brake bleeding to get a firm brake pad after air exhaustion.
9.Throttle reset: The throttle body is a tube containing a pivoting flat valve (butterfly) that is used to control the amount of air entering an engine. In an electronically fuel injected car, a throttle position sensor and air flow sensor communicate with the computer, which supplies the corresponding amount of fuel needed at the injectors. It must need re-learning throttle sensor position after clearing or repair
10.Injector Coding:Leaking injectors and some dead injectors can be missed even when an injector is disabled. Other problems with the ignition system and mechanical components also may not show an rpm loss when an injector is turned off.
11.Gear Learning:After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or the DTC 'tooth not learned' is present, tooth learning must be performed.
12.Suspension Matching:Adjust the vehicle height sensor for level calibration.
13.Sunroof Initialization:Set the sunroof lock off, close in rain, memory function of sliding 1 tilting sunroof, outside temperature threshold, etc.
14.Battery Matching:By clearing the original breakdown information about the lack of battery power,rematch the battery.
15.A/F Reset:Applied to set or lean Air/Fuel ratio parameters.
16.Steering Angle Reset:helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration."

Reading Codes

Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset

Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream

Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status

Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream

Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data

Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test

Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test

Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information

Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test

Certain vehicle components can be actuated by commands sent from the scanner to test their operability

Support 8 Multi-Langauge

Do you want to use your native language for diagnosis? Don’t worry, THINKCAR THINKSCAN provides multiple languages for you to switch ，English , French , Spanish , German , Russian , Italian , Portuguese , Japanese

Support 93+ Worldwide Vehicle Coverage

For AUDI , For BENZ , For BMW , For CHRYSLER , For CITROEN , For DACIA , For DAEWOO , For FIAT , For GM , For HOLDEN , For HONDA , For HYUNDAI , For JAGUAR , For JPISUZU , For KIA , For LANDROVER , For MAHINDRA , For MARUTI , For MAZDA , For MINI , For MITSUBISHI , For NISSAN , For OPEL , For PEUGEOT , For PORSCHE , For RENAULT , For SAAB , For SEAT , For SKODA , For SMART , For SPRINTER , For SUBARU , For SUZUKI , For TATA , For TOYOTA , For USAFORD , For VOLVO , For VW...Updating
Please contact customer service for specific details

How to Register/Update Thinkscan Max

"1.Initial Use
2.Turn on the Machine
3.Language Setting
4.Connect WIFI
5.Choose Time Zone
6.User Agreement
7.Create an Account
8.Typing in Business Information"

FAQ:

"Here we list some common questions and answers related to this tool.
Q: Why does it have no responses when connected to a car computer?
A: Check whether the connection with the vehicle diagnostic socket is normal, whether the ignition switch is on, and whether the tool supports the car.

Q: Why does the system stop while reading the data stream?
A: This may be caused by loose diagnostic dongles. Please unplug the dongle and reconnect it firmly.

Q:Communication error with vehicle ECU?
A: Please confirm:
1.Whether diagnostic dongle is correctly connected.
2.Whether ignition switch is ON.
3. If all checks are normal, send vehicle year, make, model and VIN number to us using
Feedback feature.
Q: Why does the host screen flash when the engine ignition starts?
A: It is normal and caused by electromagnetic interference.

Q: How to upgrade the system software?
A: 1. Start the tool and ensure a stable Internet connection.
2.Go to ""Set up"" -> ""App Update"", click ""OTA"" and then click ""check version"" to enter the system upgrade interface.
3. Complete the process by following the instructions on the screen step by step. It
may take a few minutes depending on the internet speed. please be patient. After successfully completing the upgrade, the tool will automatically restart and enter the main interface.

Q: Please explain the account and points.
A: To use THINKSCAN Max, you need to register an account. Each account has the opportunity to earn points by recommending others to buy products and participating in official events. 1 point can be deducted for 1 dollar when purchasing products or services

Q: How to capture the screenshot?
A: A""Screenshot"" icon is always floating on the screen. Tap it to capture the current screen and the screenshot is saved in the Think File module."

Product Parameters:

"Display Screen ：5.99-Inch/TFT(IPS)
Connection :Wi-Fi/Bluetooth
RAM:2G
ROM:16G
Working Temperature : 32℉~122℉
Storage Temperature: -4℉~144℉"

Packing List:

"1*Thinkcar Thinkscan Max Host
1*Diagnostic dongle
1*Charging cable
1*power adapter"